10 Best Go Cutter -According To Experts

What to Consider When Choosing the Best Manual go cutter

The Best Manual go cutter saves time compared to wet saws. They’re simple to use and produce faultless results. Not all manual go cutterare effective. This section explains how to choose the best manual tile cutter.

Material Cutters

“go cutter” is a misnomer. Manual tools score and snap tiles rather than cut them. Small, pointed wheels scratch the tile’s surface, creating the perfect location for a clean snap.

Wheel material affects tool performance. Tungsten carbide-tipped wheels endure longer than steel wheels while scoring tiles. Even if you’re only cutting materials for one job, utilizing the same wheel ensures accuracy.

Cutter-Bed

go cutter beds are also crucial. There are some specific characteristics that can improve the usability of your manual go cutter.

go cutter have central ridges. Best manual tile cutters have foam or rubber on either side of the ridge. This foam or rubber creates a nonslip surface that keeps tiles in place while scoring or snapping, improving accuracy and reducing waste.

Foam or rubber supports the tile while absorbing snapping pressure. Without giving, you couldn’t snap tiles cleanly.

Cutter base

You may not notice the characteristics and differences in the bases of different manuals go cutter. Larger tiles benefit from rubber feet and foldable sidebars.

It’s hard to provide continuous downward pressure while scoring larger tiles. On flat surfaces, a tile cutter without rubber feet can skid. It’s irritating and superficial.

Folding base sidebars support wide tiles and give stability when scoring and snapping. Cutting a wide tile off to one side creates uneven leverage. Sidebars allow for a more accurate, less uncomfortable cut.

Horizontal and angle rulers

Many of the greatest manual go cutter have built-in measurement instruments to speed up, improve, and maintain accuracy. These features allow repetitive cutting without measuring.

Best go cutterhave built-in horizontal rulers for trimming tiles. Some rulers extend to measure tiles that overhang the base.

Angle guidelines are convenient and consistent. Once you know the angle to cut, locate and lock the adjustable guides. You can register the tile against the guide to score and snap accurately.

How To Replace go cutter Blade?

Nearly every warehouse has a cutter, often known as a go cutter. These knives, which have a short blade and a compact design, may easily cut open cardboard boxes and take off packaging tape and other shipping-related wrappings. Box cutters are frequently built of extremely durable plastic or metal due to the trauma they endure.

go cutter are often viewed as disposable by warehouse workers. Workers in the warehouse will often start looking for a new one as soon as the blades begin to wear out. Fortunately, your organization doesn’t have to continually spend money on new box cutter purchases each week. Simply replacing the blade is a straightforward fix. The best thing, though? They frequently include bonuses!

Opening The go cutter

Finding out how a box cutter opens is the first step in replacing the blade. In our example, we only need to remove one side screw with a Phillips head screwdriver. Simply take the top off after removing the screw to divide the knife in half.

Identifying Components

The actual number of parts in our go cutter is just five. The handle, screw, blade, housing for the blade, and a pack of extra blades. We can remove the blade and blade housing from the knife after the blade has been opened.

When you get to this stage, be careful to pay attention to how the knife is positioned in the housing. Once you’ve taken note of this, you can remove the knife from the housing and properly dispose of it.

Replacing Blades

The spare blades are often contained in a little pack. They frequently arrive in sets of three to five. You should carefully take these blades out of the knife. To avoid getting sliced, locate the

extra blades in the go cutter handle. Next, unwrap the blades and take one out of the box. Put the other blades back into the handle once the new one is out.

Next, insert the new blade into the housing in the same manner you did with the old one. This knife’s blades have a two-notch system that must be properly reinstalled into the housing. This gives the blade a wonderful, secure hold.

Putting The go cutter Back Together

We should now begin putting the go cutter back together. Reinstall the blade and housing in the handle, check that the extra blades are correctly placed, and then reattach the handle’s top to its base. Your go cutter will then be in like-new condition when you tighten the screw back into place.

When reinstalling the screw, make sure you tighten it just enough to hold it in place. Overtightening the screw will compress the handle and impede the movement of the blades in the handle. To prevent this, tighten it and then test it by repeatedly opening and closing the go cutter to ensure that it is at a comfortable resistance.

3 Features of a go cutter

The following characteristics are necessary for a heavy-duty go cutter. Don’t buy it if even one component is missing. If you choose a less expensive model made of plastic or with a snap-off blade, it is not worth it because you will wind up spending more money replacing it more frequently.

Finger notch and grip

A handle that is comfortable for your fingers will have a deep notch that will stop your finger from creeping up near the blade as you cut. To prevent your hand from slipping while squeezing through tight materials, it should also feature a secure and non-slip grip.

Metal body

Spend a little more money to purchase a tool with a metal body because go cutter with a plastic body won’t be able to survive continuous use on the job site.

Easy blade change

Frequently, standard box cutters don’t have changeable blades and need a screwdriver to do so. When your go cutter blade becomes dull, you can easily replace it using a thumbscrew or finger release instead of searching for a screwdriver. To ensure that you always have extra blades on hand for quick swaps, look for a go cutter with a blade storage system.

Ergonomics

Ergonomics is a top consideration in our design process. We always look for new ways to make our tools more comfortable and easier to use. This helps cut down on fatigue and reduces overuse injuries. It’s also why several of our tools look different from anything else you’ve ever seen.

Tool-Free Blade Changes

When you need to change a blade, you don’t need another tool to get the job done. You change blades less frequently because our blades last longer, and you change them easily.